are cam2 control run history and restart files available?

[jane@gi_alaska_edu]

Hi, I wonder if cam2 history files and restart files of control run available. I couldn't find any in the directory: /CCSM/csm/b20.007/atm/hist or /CCSM/csm/b20.007/atm/rest in MSS storage. And I checked earth system grid too,but there is only output data from CCSM3.
So does anybody know where I can find history and restart files for CAM2? Thanks in advance!

 

[murphys]

Jane,

If you are looking for stand alone CAM runs, you are in the wrong place. This is
the CCSM fully coupled part of the bullitan board. That said, a version of CAM is used in the coupled model and there are atmospheric history files available for
on the mass store or earth system grid (http://www.earthsystemgrid.org) for various
different model runs.

b20.007 is a CCSM run, so I suspect you are looking for stand alone CAM.

Let us know.

 

[jane@gi_alaska_edu]

Hi Sylvia,
I am sorry, I didn't make it clear. I am looking for fully coupled CCSM2.0.1 model output, not just CAM2 runs. The reason I refered to CAM2 history and restart files was because the fully coupled CCSM2.0.1 model used CAM2 as the atmophere component.
Thanks and regards
Zhao

 

[murphys]

I just did an msls on that model case (b20.007) which is the only control run
available from ccsm 2.0.1.

there are tons of history files available in /CCSM/csm/b20.007/atm/hist

b20.007.cam1.h0.1339-04.nc b20.007.cam1.h1.1344-04-11-00000.nc
b20.007.cam1.h0.1339-05.nc b20.007.cam1.h1.1344-05-11-00000.nc
b20.007.cam1.h0.1339-06.nc b20.007.cam1.h1.1344-06-10-00000.nc
b20.007.cam1.h0.1339-07.nc b20.007.cam1.h1.1344-07-10-00000.nc
b20.007.cam1.h0.1339-08.nc b20.007.cam1.h1.1344-08-09-00000.nc
b20.007.cam1.h0.1339-09.nc b20.007.cam1.h1.1344-09-08-00000.nc
b20.007.cam1.h0.1339-10.nc b20.007.cam1.h1.1344-10-08-00000.nc
b20.007.cam1.h0.1339-11.nc b20.007.cam1.h1.1344-11-07-00000.nc
b20.007.cam1.h0.1339-12.nc b20.007.cam1.h1.1344-12-07-00000.nc
b20.007.cam1.h0.1340-01.nc b20.007.cam1.h1.1345-01-06-00000.nc
b20.007.cam1.h0.1340-02.nc b20.007.cam1.h1.1345-02-05-00000.nc
b20.007.cam1.h0.1340-03.nc b20.007.cam1.h1.1345-03-07-00000.nc

these are labeled cam1 and not cam2 however. The rest sub-directory is equally populated.

was there a particular reason these files were not what you were looking for?

 

[jane@gi_alaska_edu]

I am running CCSM2.0.1 fully coupled model with atmosphere component of CAM2, so if there is any control run output of cam2 available, that would save me a lot of work.
Thanks and regards!

 

[murphys]

there was only one control run for ccsm 2.0.1. That is case b20.007 which was
run with cam1. so, there are no control runs run with cam2.